Fix My Door Now OttawaA Can-Lock Security Company
Services Before & After Service Areas About Blog FAQ Contact
📞 613-265-DOOR Request a Free Quote
Residential • Commercial • Industrial Ottawa Same-Day Door Repair — Call 613-265-DOOR OPEN 24 HOURS / 7 DAYS A WEEK ✓
Home  /  Door Problem Finder

What’s Wrong With Your Door?

Interactive Door Troubleshooting Tool

Use our free interactive Door Problem Finder to identify possible causes, get troubleshooting tips, and explore repair solutions.

Free • Takes 1–2 minutes • No signup required

Aussi disponible en français

Door troubleshooting guide

Every problem in the Door Problem Finder, grouped by type. Open a problem to see the causes, safe checks, warning signs and what the repair involves. A real door diagnosis needs someone to see the door, so use this as a starting point and call us when the warning signs apply.

Closing, latching and locking

Doors that will not close, latch, lock or open freely. Most of these come down to hinges, the strike or the frame moving.

The door won't close or latch

Applies to: Front or entry door, Interior door, Commercial or storefront · Common in winter
Possible causes
  • The door has dropped on worn or loose hinges, so the latch now hits below or beside the strike.
  • The frame or house has moved with the seasons. Ottawa doors often latch fine in summer and stop in winter, or the reverse.
  • On a commercial door, the closer has slowed down in the cold or is leaking oil, so the door stops short.
Safe checks you can do
  • Look at the edge of the door near the latch. A fresh scrape on the strike plate shows where the latch is hitting.
  • Tighten the hinge screws with a screwdriver. Loose top hinge screws are a common and easy fix.
  • Close the door slowly and watch whether the latch lines up with the hole in the strike.
Warning signs: call a professional

If tightening the hinges does not fix it, if the gap at the top corner is wider than at the bottom, or if it is a commercial or fire-rated door that must close on its own.

What the repair usually involves

Usually an adjustment: tightening or shimming hinges, moving or replacing the strike, or a closer adjustment on commercial doors. Rebuilding the jamb is needed only when the frame is damaged.

The door sticks, rubs or drags

Applies to: Front or entry door, Interior door
Possible causes
  • Humidity has swollen a wood door, usually in summer.
  • The door has sagged on its hinges and now rubs the frame at the top on the latch side.
  • The frame has shifted or been damaged, so the opening is no longer square.
Safe checks you can do
  • Find where it rubs: shiny or worn paint on the door edge or the frame shows the spot.
  • Tighten all hinge screws. If one spins without biting, the hole is stripped.
  • Notice whether it only sticks in humid weather. Seasonal sticking is often a planing and sealing job.
Warning signs: call a professional

If it rubs in more than one spot, the gap around the door is uneven, or the door is getting harder to close each season.

What the repair usually involves

Re-hanging the door on its hinges, adjusting the strike, or planing and sealing the edge that rubs. A damaged or out-of-square frame is repaired before the door is adjusted.

The key is hard to turn or the deadbolt won't lock

Applies to: Front or entry door, Commercial or storefront · Common in winter
Possible causes
  • The deadbolt is hitting the edge of the strike because the door has moved, so it cannot throw fully.
  • The lock cylinder is dirty, worn or has moisture frozen inside it.
  • The key itself is worn, or is a poor copy.
Safe checks you can do
  • Open the door and turn the deadbolt. If it moves easily with the door open but not closed, the problem is alignment, not the lock.
  • Try a different copy of the key.
  • In winter, use lock de-icer rather than hot water.
Warning signs: call a professional

If the bolt only locks when you push or pull the door, the lock is stiff even with the door open, or the key has started to bend.

What the repair usually involves

Re-aligning the strike so the bolt throws freely, servicing or replacing the lock cylinder, or replacing the lock.

The door is frozen shut

Applies to: Front or entry door, Patio or sliding door · Common in winter
Possible causes
  • Water or melted snow has refrozen between the door and the threshold or seal.
  • A gap in the seal lets moist indoor air reach the cold outer edge, where it freezes.
  • On a sliding door, ice has built up in the bottom track.
Safe checks you can do
  • Push firmly near the frozen edge rather than yanking the handle.
  • Use warm (not boiling) water or a hair dryer on the seal line, then dry it.
  • Clear snow away from the threshold and track so it cannot melt and refreeze.
Warning signs: call a professional

If it freezes shut repeatedly, the seal is torn, or water is getting in under the door.

What the repair usually involves

Freeing the door without tearing the seal, then fixing the cause: a worn seal, a door that no longer closes tight, or water reaching the threshold.

Drafts, frost and water

Cold air, frost and water around a door. Worn seals are the usual cause; water left too long leads to rot.

Cold air comes in around the door

Applies to: Front or entry door, Patio or sliding door, Commercial or storefront · Common in winter
Possible causes
  • The weatherstripping is flattened, torn or missing in places.
  • The door sweep or bottom seal is worn, or the threshold is set too low.
  • The door no longer closes tight against the stop because it has shifted.
Safe checks you can do
  • On a windy day, run the back of your hand around the edges of the closed door.
  • Look for daylight around the door from inside with the lights off.
  • Close the door on a sheet of paper. If it slides out easily, the seal is not touching there.
Warning signs: call a professional

If the seals are worn all around, the door does not press evenly against the weatherstripping, or there is ice or frost forming at the gap.

What the repair usually involves

Replacing worn weatherstripping and the door sweep, and adjusting the door so it closes evenly against the new seal.

Frost or condensation on the door or frame

Applies to: Front or entry door, Patio or sliding door · Common in winter
Possible causes
  • Cold air is getting past a worn seal and chilling one spot below the dew point.
  • High indoor humidity meeting a cold door surface, common on steel doors and older sliders.
  • A failed seal in an insulated glass unit, which shows as fog between the panes.
Safe checks you can do
  • Note where the frost forms. Frost at one edge or corner usually points to a seal gap there.
  • Wipe the glass. Moisture you can wipe off is on the surface; fog that stays is inside the glass unit.
  • Check your indoor humidity. Very high humidity in winter causes condensation on any cold surface.
Warning signs: call a professional

If frost keeps forming in the same spot, the seal is damaged, or the glass is fogged between the panes.

What the repair usually involves

Finding the gap and replacing the seal there, adjusting the door so it closes tight, or replacing a fogged glass unit.

Water comes in under the door, or the floor is soft

Applies to: Front or entry door, Patio or sliding door
Possible causes
  • The sill or threshold is worn, cracked or not sealed to the frame.
  • The door sweep no longer touches the threshold.
  • Water has already rotted the subfloor or the bottom of the frame, which then lets more in.
Safe checks you can do
  • Look for staining, swelling or peeling at the bottom of the frame and on the floor inside.
  • Press the floor right inside the door. A soft or spongy spot is a warning sign.
  • Check the outside slope. Water should run away from the door, not toward it.
Warning signs: call a professional

As soon as you see soft flooring, dark staining or mould near the door. Water damage spreads under the floor long before it shows.

What the repair usually involves

Resealing or replacing the threshold and sweep. If water has already damaged the subfloor or frame, the rotted section is cut out, rebuilt and waterproofed.

The frame or sill is soft or rotted

Applies to: Front or entry door, Patio or sliding door
Possible causes
  • Water has been getting into the bottom of the frame for years, usually from a failed sill seal or splash-back.
  • Paint or caulking has failed, letting water soak into bare wood.
  • Snow piled against the door melts and soaks the frame every spring.
Safe checks you can do
  • Press a screwdriver into the bottom of the frame. Sound wood resists; rot lets the tip sink in.
  • Look for peeling paint, dark staining or gaps between the frame and the sill.
  • Check inside for staining on the floor or baseboard near the door.
Warning signs: call a professional

If the screwdriver sinks in, or the door has started to sag or leak. Rot can usually be repaired by replacing the damaged section before the whole door has to go.

What the repair usually involves

Cutting out the rotted section of the frame or sill, rebuilding it, and sealing it so water cannot get back in. Severe damage may mean a new frame.

Patio and sliding doors

Sliding doors that drag, jump the track or do not lock securely. Worn rollers cause most of these.

The patio door is hard to slide or came off its track

Applies to: Patio or sliding door · Common in winter
Possible causes
  • The rollers are worn or seized, so the panel drags on the track.
  • The track is dirty, bent or packed with ice and grit.
  • The panel has jumped the track, often after being forced or lifted.
Safe checks you can do
  • Vacuum the bottom track and wipe it clean. Debris is the cheapest thing to rule out.
  • Look at the bottom of the panel. If it sits low or touches the track, the rollers are worn or need adjusting.
  • Do not force a door that has come off its track. The glass panel is heavy.
Warning signs: call a professional

If cleaning does not help, the door grinds or scrapes, or the panel is off the track.

What the repair usually involves

Taking the panel out, replacing the rollers, cleaning or repairing the track, and adjusting the door so it slides and latches properly.

The patio door won't lock or doesn't feel secure

Applies to: Patio or sliding door
Possible causes
  • The panel has dropped on worn rollers, so the latch no longer reaches the keeper.
  • The latch or keeper is bent or worn.
  • There is no second lock, so the small latch is the only thing holding the door.
Safe checks you can do
  • Lock the door and try to slide it from inside. It should not move at all.
  • Check whether the latch lines up with the keeper when the door is closed.
  • A dowel in the bottom track is a quick stopgap while you arrange a proper fix.
Warning signs: call a professional

If the latch does not catch, or you want a security bar, anti-lift blocks or a second lock installed.

What the repair usually involves

Adjusting the rollers so the latch lines up, replacing a worn latch or keeper, and adding a security bar, anti-lift blocks or a second lock.

Break-ins, frames and glass

Forced doors, split frames and broken glass. These need to be secured first, then repaired properly.

The frame is split or the door was forced

Applies to: Front or entry door, Commercial or storefront
Possible causes
  • The door was kicked or pried, and the jamb split at the strike where the screws only held into thin trim.
  • The strike plate tore out, so the deadbolt no longer has anything solid to lock into.
  • Hinges or the hinge-side jamb were bent by the force.
Safe checks you can do
  • If it was a break-in, call the police first and take photos before anything is moved.
  • Check whether the door still closes and locks. If not, it needs securing tonight.
  • Look at the jamb around the strike for cracks that run up or down the frame.
Warning signs: call a professional

Right away if the door will not lock. A split jamb is repaired by rebuilding the frame and installing a reinforced strike, not by screwing the old strike back on.

What the repair usually involves

Securing the door first, then rebuilding the split jamb, installing a reinforced strike with long screws into the framing, and realigning the door.

The glass in the door is cracked or broken

Applies to: Front or entry door, Patio or sliding door, Commercial or storefront
Possible causes
  • Impact, including a break-in attempt.
  • Stress from a door that slams or a frame that has shifted.
  • On insulated glass, a failed seal shows as fog between the panes rather than a crack.
Safe checks you can do
  • If the glass is broken, keep people and pets away and do not try to pull out loose pieces.
  • Check whether the door can still be closed and locked safely.
  • Note the size of the glass and whether it is tempered (often marked in a corner).
Warning signs: call a professional

Right away if the glass is broken or the door cannot be secured. We board up the opening and replace the glass once it is sourced.

What the repair usually involves

Securing the opening right away, often with a board-up, then installing replacement glass once it is sourced.

Commercial and automatic doors

Closers, storefronts and automatic or accessible entrances. These doors have safety and code requirements, so adjustments belong to a technician.

A commercial door slams or closes too slowly

Applies to: Commercial or storefront · Common in winter
Possible causes
  • The closer needs adjusting. Its sweep and latch speeds drift, and cold weather slows it down.
  • The closer is leaking oil and can no longer control the door.
  • Worn hinges or pivots let the door drop and bind.
Safe checks you can do
  • Look at the closer body for oil. An oily closer is worn out.
  • Watch the full swing: a door that races then stops short, or slams the last few inches, needs adjustment.
  • Check that nothing at the floor, such as ice, a mat or a worn threshold, is catching the door.
Warning signs: call a professional

If adjustment does not hold, the closer is leaking, or it is a fire-rated door that must close and latch on its own.

What the repair usually involves

Adjusting the closer’s sweep and latch speeds, replacing a leaking closer, or repairing worn hinges or pivots.

An automatic or accessible door is acting up

Applies to: Commercial or storefront · Common in winter
Possible causes
  • Ice, slush or salt in the floor guide makes a sliding door drag, and the operator reverses because it reads the drag as an obstruction.
  • The sensors are picking up snow, wind or people walking past, so the door opens on its own.
  • On a swing operator, wind pressure or ice at the threshold stops the door, or a push button has filled with water.
Safe checks you can do
  • Clear the floor track and the area under the panels.
  • Watch a full cycle: does it drag, reverse, or open with nobody there?
  • Press each push button, inside and out.
Warning signs: call a professional

If the door reverses, opens by itself, grinds, or an accessible entrance stops working. Sensor range, hold-open time and force can be adjusted, and worn parts replaced.

What the repair usually involves

Adjusting sensors, hold-open time and force, replacing worn guides, rollers or push buttons, and checking the operator. Safety devices are set by a technician, never bypassed.

Garage doors

Garage door springs and cables are under high tension. Check, but leave adjustments to a technician.

The garage door won't open or close

Applies to: Garage door · Common in winter
Possible causes
  • A broken spring: the opener runs, but the door is too heavy to lift.
  • The opener has no power, the remote or wall button has failed, or the emergency release has been pulled.
  • The door has come off its track or a cable has slipped.
Safe checks you can do
  • Make sure the opener has power and try the wall button as well as the remote.
  • Look at the spring above the door from a distance. A gap in the coil means it has broken.
  • Do not pull the emergency release or lift the door by hand if a spring or cable looks broken. The door can drop.
Warning signs: call a professional

If the opener runs but the door does not move, the door is crooked or off its track, or a spring or cable looks broken.

What the repair usually involves

Finding why the door will not move, then repairing the spring, cable, track or opener. Spring and cable work is always done by a technician.

The garage door is noisy, shakes or jerks

Applies to: Garage door
Possible causes
  • Dry or worn rollers, hinges and bearings.
  • Loose track brackets or hinges that rattle as the door moves.
  • A worn opener drive, or a spring that is losing tension so the opener strains.
Safe checks you can do
  • Watch and listen to a full cycle to find where the noise comes from.
  • Lubricate the hinges and roller stems with a garage door lubricant. Do not grease the tracks.
  • Notice whether the door moves evenly or jerks, sags or stops partway.
Warning signs: call a professional

If you hear grinding, banging or popping, the door shudders or sags on one side, or the noise came on suddenly.

What the repair usually involves

Lubricating and replacing worn rollers, hinges and bearings, tightening hardware, and checking spring balance and the opener.

A garage door spring or cable is broken, or the door hangs crooked

Applies to: Garage door · Common in winter
Possible causes
  • A torsion spring has snapped. Many people hear a loud bang.
  • A lift cable has frayed, broken or slipped off its drum.
  • One side of the door has come off its track.
Safe checks you can do
  • From a safe distance, look for a gap in the spring coil or a loose, hanging cable.
  • Keep people, pets and cars out from under the door.
  • Do not run the opener or try to lift or adjust the door. Springs and cables are under very high tension.
Warning signs: call a professional

Right away. Spring and cable repairs are always for a technician.

What the repair usually involves

Replacing the broken spring or cable, putting the door back on its track and balancing it so the opener does not strain.

The garage door reverses or won't close all the way

Applies to: Garage door · Common in winter
Possible causes
  • The safety sensors near the floor are dirty, blocked or knocked out of line. Low winter sun can also blind them.
  • Ice, snow or something on the floor is stopping the door.
  • The opener's close or force settings have drifted.
Safe checks you can do
  • Wipe both sensor lenses and check that their lights are on and steady.
  • Clear the floor under the door.
  • Never tape over or disconnect the sensors. They stop the door from closing on people and pets.
Warning signs: call a professional

If it still reverses after cleaning the sensors, or if the door does not reverse when something is in its way.

What the repair usually involves

Aligning and testing the safety sensors, adjusting the opener’s close and force settings, and checking the door’s balance and travel.

The garage door is frozen to the floor, or the bottom seal is torn

Applies to: Garage door · Common in winter
Possible causes
  • Melted snow refreezes under the bottom seal overnight.
  • The bottom seal is worn or torn, letting in water, cold air and snow.
  • The floor is uneven or sloped where the door meets it.
Safe checks you can do
  • Do not run the opener against a frozen door. It can tear the seal or strain the opener.
  • Free the seal gently with warm (not boiling) water or a plastic scraper, then dry the floor.
  • Look along the bottom seal for tears, flattened spots or daylight.
Warning signs: call a professional

If the seal is torn, the door no longer closes tight, or it freezes down repeatedly.

What the repair usually involves

Replacing the bottom seal and adjusting the door so it closes evenly against the floor.

This finder gives general information to help you understand a door problem. It is not a diagnosis of your specific door. Never adjust garage door springs or cables, electrical or automatic door safety equipment, or fire-rated door hardware yourself. If a door cannot be closed or locked safely, or there is broken glass or structural damage, call a professional.

More seasonal checklists and guides: Ottawa Home Maintenance Hub.

📞 613-265-DOOR